Build a First Workbench: Height, Cut List, Fasteners
A first workbench that works is a 48-by-24-inch frame of six 8-foot 2x4s, two plywood panels, eight steel connectors and a box of screws, with a working surface just over 36 inches off the floor. Simpson Strong-Tie publishes exactly that design as its heavy-duty workbench project: six 2x4s, one 4-by-4-foot sheet of 5/8-inch plywood cut into two 24-by-48-inch shelves, one 2-by-4-foot sheet of 1/4-inch pegboard, and eight RTC2Z Rigid Tie corner connectors. Every cut is straight, and the manufacturer says no predrilling is needed for the connector screws.
Four numbers decide whether that plan comes out square and comfortable: the real size of a 2x4, the kerf the saw removes, the true thickness of “5/8” plywood, and the height that suits the work. The cut list below assigns every part to a board with those numbers built in.
Quick facts for the 48 x 24 in. bench
| Item | Specification | Source |
|---|---|---|
| Footprint | 48 in. wide, 24 in. deep (panel size) | Simpson Strong-Tie plan |
| Lumber | Six 2x4 x 8 ft | Simpson Strong-Tie plan |
| Panels | Two 24 x 48 in. in 5/8 in. plywood, one 24 x 48 in. in 1/4 in. pegboard | Simpson Strong-Tie plan |
| Connectors | Eight RTC2Z | Simpson Strong-Tie plan |
| Front posts | 36 in.; work surface about 36-5/8 in. with the top on the post ends | Plan; surface height calculated below |
| Rear posts | 58 in. (carry the pegboard) | Simpson Strong-Tie plan |
| Published load rating | None stated | Simpson Strong-Tie plan |
How tall should a workbench be?
The common rule is wrist height. Christian Becksvoort, writing in Fine Woodworking issue 265, puts it this way: “The rule of thumb is that the bench should come up to about your wrist.” He adds that standard benches are usually 36 inches tall, and that the height should suit your own size (Fine Woodworking).
The reason height matters is the work. Planing takes upper-body strength, so a lower bench is better, while sawing dovetails and carving are easier on the back at a higher surface. Becksvoort’s own bench is 39 inches. For planing or sanding large panels he stands on a 2-3/4-inch platform, which makes the surface effectively 36-1/4 inches high, and for carving and inlay he clamps on a 12-inch auxiliary bench whose top is 51 inches off the floor.
Richard Maguire of The English Woodworker divides benches into three bands and offers a way to measure yourself (The English Woodworker):
| Bench | Height | Suits |
|---|---|---|
| Low | 29-30 in. (74-76 cm) | Hand work, especially hand thicknessing, with body weight over the bench |
| Average | 34-36 in. (86-91 cm) | A mix of activities; the most common height |
| Tall | 38-39 in. (97-99 cm) | Detailed work, cutting joinery and power-tool use |
His personal-height method: stand in your workshop shoes, arms straight, palms flexed up and parallel to the floor, and measure from the floor to the underside of the palm. Add a couple of inches for mixed work, and another inch or two for delicate close work or a bad back. He also notes that an inch or so makes little difference.
On this plan the top panel spans the 36-inch front posts, and only its back corners are notched around the taller rear posts. With the panel resting on the post ends, the surface sits at the post height plus the panel’s actual thickness: 36.59 to 36.66 inches for a 5/8 Performance Category sheet, or about 36-5/8 inches. That is close to Becksvoort’s 36-inch standard and just above Maguire’s average band. To change the height, alter all four posts by the same amount and set the top connectors on the rear posts level with the new front-post tops. The rails and shelves stay the same size, because they set only the footprint. Raising the bench by more than 3-5/8 inches leaves boards 3 and 4 in the cut list below too short for a rear post plus two end rails.
Real lumber sizes decide whether the frame fits
A 2x4 is not 2 by 4 inches. The American Softwood Lumber Standard, NIST Voluntary Product Standard PS 20, defines the nominal size as “the label designation for lumber size categories that does not reflect the dressed size,” and gives the example that “a dry 2 by 4 is surfaced to 38.1 mm by 88.9 mm (1 1/2 by 3 1/2 inches)” (NIST PS 20-25). NIST’s own explainer on lumber standards gives the same finished 1.5-by-3.5-inch figure (NIST). The full chart is on the nominal vs actual lumber sizes page.
The plan’s panel sizes agree with the actual dimensions when each post’s 3-1/2-inch side runs front to back. Two 1-1/2-inch post thicknesses plus a 45-inch rail make 48 inches; two 3-1/2-inch post widths plus a 17-inch end rail make 24 inches. The plan does not print these sums, but they match the 24-by-48-inch panels exactly. Draw the same frame with nominal 2-by-4-inch posts and it grows to 49 by 25 inches, an inch wider and an inch deeper than the shelves.
Length is different. PS 20 says standard lengths are multiples of 1 foot or 2 feet, and lumber 2 inches or less in nominal thickness is double-end trimmed unless the contract says otherwise. Treat an “8-foot” board as 96 inches and measure each one before marking, since the plan’s tightest boards leave only 3-5/8 inches to spare.
Cut list for six 8-foot 2x4s
The parts, from Simpson Strong-Tie’s list, with actual sizes and the board or sheet each comes from:
| Part | Qty | Actual size | Cut from |
|---|---|---|---|
| Front and back horizontal rails | 4 | 1-1/2 x 3-1/2 x 45 in. | Boards 1 and 2 (two each) |
| Rear corner posts | 2 | 1-1/2 x 3-1/2 x 58 in. | Boards 3 and 4 (one each) |
| End rails | 4 | 1-1/2 x 3-1/2 x 17 in. | Boards 3 and 4 (two each) |
| Top back rail | 1 | 1-1/2 x 3-1/2 x 48 in. | Board 5 |
| Front corner posts | 2 | 1-1/2 x 3-1/2 x 36 in. | Board 6 |
| Shelves | 2 | 24 x 48 in. on the plan; 0.594 to 0.656 in. thick (5/8 Performance Category) | One 4 x 4 ft sheet of 5/8 plywood |
| Pegboard back | 1 | 24 x 48 in., 1/4 in. thick | One 2 x 4 ft sheet, used whole |
Kerf check for each board
A saw removes material at every cut, and each piece takes one cut to free it from the rest of the board. This table assumes a 1/8-inch kerf and a 96-inch board; measure the slot your own blade cuts and substitute it.
| Board | Pieces | Total of pieces | Cuts | Used, with kerf | Left over |
|---|---|---|---|---|---|
| 1 and 2 (each) | 45 + 45 | 90 in. | 2 | 90-1/4 in. | 5-3/4 in. |
| 3 and 4 (each) | 58 + 17 + 17 | 92 in. | 3 | 92-3/8 in. | 3-5/8 in. |
| 5 | 48 | 48 in. | 1 | 48-1/8 in. | 47-7/8 in. |
| 6 | 36 + 36 | 72 in. | 2 | 72-1/4 in. | 23-3/4 in. |
The 2x4 parts total 484 inches against 576 inches of stock, so 92 inches of offcut remains before kerf and 90-3/8 inches after the 13 cuts. The margin is thin only on boards 3 and 4, where squaring a split or rough end comes straight out of the 3-5/8 inches. Give those positions to the two boards with the soundest ends, cut the 58-inch post before the short rails, and keep the 47-7/8-inch offcut from board 5 as a spare for any 45-, 36- or 17-inch piece that goes wrong.
Mark each piece after cutting with its part name and an arrow for the end that goes up. Measure and cut the first piece of every repeated length, then match the rest to it.
Plywood and pegboard: the 24-inch problem
The plan calls for two 24-by-48-inch shelves from one 4-by-4-foot sheet of 5/8-inch plywood. A saw kerf comes out of that 48-inch width, so two exact 24-inch panels are not possible from it. The standard also lets a panel run small: PS 1, the NIST structural plywood standard, allows a size tolerance of plus zero, minus 1/16 inch on the stated length and width (NIST PS 1-22). Split evenly with a 1/8-inch kerf, each shelf comes out about 23-15/16 inches deep; cut the top shelf to a true 24 inches instead and the lower one comes out about 23-7/8. Either way the shelf edges still land on the front and back rails, so the shortfall does not stop a shelf from sitting properly.
Thickness works the same way. PS 1 labels panels by Performance Category, not measured thickness. For a “5/8” sanded panel it allows 0.609 to 0.641 inch; for an unsanded one, 0.594 to 0.656 inch. A sheet called 3/4-inch can be either the 23/32 category (0.703 to 0.734 inch sanded) or the 3/4 category (0.734 to 0.766 inch sanded). A 23/32 top is about 0.09 inch thicker than a 5/8 one, the next step up if a stiffer top is wanted, and puts the work surface at about 36-23/32 inches. PS 1 requires each panel’s stamp to show its thickness in thousandths of an inch, so read it in the store rather than assuming.
The notches follow the plan. Place a 2x4 on each corner of the shelf, trace it and cut to clear the corner posts; only the back corners of the top shelf are notched, and all four corners of the lower shelf. Trace from the actual posts, not from a drawing, so the notch matches the 1-1/2-by-3-1/2-inch section.
The pegboard back is the whole 1/4-inch, 2-by-4-foot sheet (24 by 48 inches), fastened with #8 x 1-1/4-inch wafer-head screws to the rear posts and the top back rail.
Fasteners and connectors
Simpson Strong-Tie lists these for the 48-inch bench (project page):
| Fastener | Quantity | Used for |
|---|---|---|
| #8 x 1-1/4 in. wafer-head screws | One box | RTC2Z connectors on posts and rails, and the pegboard |
| #6 x 1-1/4 in. bugle-head screws | 20 | Plywood shelves |
| #6 x 2-1/2 in. bugle-head screws | 4 | Top back rail |
| RTC2Z Rigid Tie connectors | 8 | Rail-to-post corners |
The page’s text calls the shelf screws “flat-head” while its product link is for a bugle-head screw, so confirm the head type against the package. The WBSK kit contains eight RTC2Z connectors and 100 #8 x 1-1/4-inch wafer-head screws, and leaves the lumber, the pegboard and the top-rail and pegboard screws to the buyer (Simpson Strong-Tie WBSK). The project page does not say where the four 2-1/2-inch screws go; they are the only screws on its list left for the top rail.
The RTC2Z is an 18-gauge steel corner connector that joins a 2x4 post to two 2x rails (joists, in Simpson’s table). Simpson’s Wood Construction Connectors catalog gives its allowable downward load per connector for three fastener schedules, in Douglas fir-larch or southern pine, with the load shared equally between the two rails (Simpson Strong-Tie catalog C-C-2021, p. 313):
| Fasteners into the post / into the rails | Allowable load, floor duration |
|---|---|
| 6 / 6 #8 x 1-1/4 in. Strong-Drive SD screws | 300 lb |
| 6 / 6 nails, 0.148 x 1-1/2 in. | 710 lb |
| 6 / 6 #9 x 1-1/2 in. Strong-Drive SD screws | 1,025 lb |
The workbench plan fastens its connectors with #8 x 1-1/4-inch screws, the size in the first row. These are design values for one connector in building framing, not a rating for the bench, and neither Simpson’s project page nor its WBSK page states a load capacity for the finished workbench.
Load, racking and squareness
Because no rating is published, treat the bench as a worktable for hand tools and light machines, and add a vise, a benchtop machine or casters only after checking what the mount needs. Keep heavy items on the lower shelf, close to the posts. A frame with square corners can still sway sideways into a parallelogram (racking), so build it square and keep the panels fastened:
- Dry-fit one side frame: two posts and two 17-inch end rails.
- Measure both diagonals of each side frame; they match when the frame is square. Fix any difference before tightening.
- Join the two sides with the 45-inch rails, then check diagonals again and place a framing square on every corner.
- Fit the plywood without forcing it, and drive the shelf screws only when the frame stays square.
The levels and squares guide explains why equal diagonals confirm squareness only alongside the other measurements.
Finally, put the bench where it will be used and check that all four feet carry weight. If a frame that checked square still rocks, the floor is uneven; shim the short foot rather than forcing the frame.
Buying checklist
Quantities below come from the plan. Prices are not listed because home-improvement retailers show different prices by store and ZIP code; read each item on the retailer’s own product page on the day of purchase, and for a full budget see the workshop cost guide.
| Item | Quantity | Check before buying |
|---|---|---|
| 2x4 x 8 ft boards | 6 | Full 96 in. length (boards 3 and 4 need 92-3/8 in. with kerf); sight along each edge; avoid cracked ends |
| 5/8 in. plywood, 4 x 4 ft | 1 | Thickness stamp in thousandths; flat; sanded face |
| 1/4 in. pegboard, 2 x 4 ft | 1 | Flat sheet, no chipped holes |
| RTC2Z connectors | 8 | Sold as the WBSK kit with 100 #8 x 1-1/4 in. screws |
| #8 x 1-1/4 in. wafer-head screws | As needed | For the pegboard; Simpson lists pegboard screws as bought separately from the kit |
| #6 x 1-1/4 in. bugle-head screws | 20 | For the shelves; confirm the head type on the package |
| #6 x 2-1/2 in. bugle-head screws | 4 | For the top back rail |
| Consumables | Blade or sandpaper, pencil, tax, delivery |
The project material calculator turns a cut list like the one above into stock lengths, which is a quick way to adapt the layout to a different bench size.
Sources
- Simpson Strong-Tie: DIY heavy-duty workbench, materials and cut list
- Simpson Strong-Tie: WBSK workbench and shelving kit contents
- NIST: PS 20-25 American Softwood Lumber Standard
- NIST: nominal and actual lumber sizes
- NIST: PS 1-22 Structural Plywood
- Fine Woodworking: Tricks for Working at the Right Height
- The English Woodworker: Workbench Height
- Simpson Strong-Tie Wood Construction Connectors catalog C-C-2021, p. 313: Rigid Tie connectors and RTC2Z allowable loads (PDF copy hosted by FastenersPlus)