Project Material Calculator: Paint, Board Feet, Buy List
Wall paint is wall area times coats divided by the product’s published spread rate: a 12 x 14 foot bedroom with 8-foot walls, one door and two windows takes 1.8 to 2.1 gallons for two coats at 350-400 square feet per gallon. Lumber is counted in board feet: thickness times width times length, all in inches, divided by 144. The purchase list is whatever those two numbers become after waste, and for hardwood the grade sets the allowance: at the National Hardwood Lumber Association’s minimum clear yields, FAS needs 20% extra wood, No. 1 Common 50% and No. 2A Common 100%. The calculator below handles the paint for a rectangular room.
Paint calculator for rectangular walls
Enter room length, width, and wall height in feet. Enter the combined measured area of openings you will exclude, the planned number of coats, and the chosen product’s coverage per gallon. This form estimates walls only; calculate the ceiling, trim, and doors separately when they use a different paint.
Enter dimensions and the product coverage to estimate wall paint. The result excludes primer and any additional allowance you choose.
The calculation runs locally in your browser and does not store a project history. It reports the paintable wall area, the gallons to two decimal places, and that figure rounded up to whole one-gallon containers, with primer and any extra allowance left as separate lines.
The paint arithmetic
Wall area = 2 x (length + width) x height, minus the openings. Gallons = wall area x coats / coverage per gallon. For the form’s default room, 12 by 14 feet with 8-foot walls, the perimeter is 52 feet and the gross wall area is 416 square feet. The default 51 square feet of openings is one 3 x 7 foot door (21) plus two 3 x 5 foot windows (30), which leaves 365 square feet. Two coats is 730 square feet of coverage to buy.
Benjamin Moore’s own paint calculator uses the same logic with fewer inputs: length, width, height, and the number of doors and windows. It states that its results “assume 2 coats of paint and do not include the ceiling” and that they are “not intended to give more than a rough estimate,” because “precise paint needs will vary according to many factors, including application method.”
Coverage per gallon: what manufacturers publish
The spread rate is the one input you cannot measure, so it comes from the label or the product page. Benjamin Moore lists coverage as a range on each product page and adds that “reported technical data is representative of the product line,” with specific bases and colors to be confirmed with the company. Glidden’s calculator page gives a single figure with its condition attached: “1 gallon of paint typically covers up to 400 sq. ft. on primed, smooth, non-porous surfaces,” and adds that “drastic color changes or porous surfaces may require more than one coat.”
The table applies each published range to the default room, 730 square feet of coat coverage on the walls. Ranges are as listed on the pages cited, as of November 2026.
| Product (published coverage) | Gallons at the lower rate | Gallons at the higher rate |
|---|---|---|
| Benjamin Moore Aura Interior (350-400 sq ft/gal) | 2.09 | 1.83 |
| Benjamin Moore ben Interior (400-450 sq ft/gal) | 1.83 | 1.62 |
| Glidden, “up to 400” on primed, smooth, non-porous surfaces | 1.83 or more | not stated |
Two readings follow. First, the same walls need 1.6 to 2.1 gallons depending on the product, a gap of half a gallon, so the product choice comes before the arithmetic. Second, the top of a published range assumes a good surface, which is how Glidden words its own figure. Planning on the lower rate is the safer choice for new drywall, textured walls, or a large color change. With one-gallon containers, 2.09 rounds up to three gallons and 1.83 rounds up to two, which is why the calculator reports the whole-container figure separately.
Separate lines: ceiling, trim, primer
Different surfaces carry different spread rates, so they belong on separate lines. Benjamin Moore lists Muresco ceiling paint at 400-450 square feet per gallon and Advance interior semi-gloss, a trim paint, at 400-500. The Advance page also lists a recoat time of 16 hours, against 1 hour for Aura matte and 2 hours for ben eggshell, which decides how many days a two-coat job takes.
Measure each opening rather than assuming a standard size, and keep a door on the door-paint line if it is painted separately. For a room with unequal wall heights, calculate each wall on its own. Primer is its own quantity whenever the surface calls for it, with the primer’s own coverage figure and its own container size.
Board feet: the formula and worked examples
A board foot is a volume of 144 cubic inches. The rulebook of the National Hardwood Lumber Association (NHLA) defines it as a piece “12” wide by 12” long and 1” thick (144 cubic inches) or the equivalent.” The formula follows from that definition:
- Board feet = thickness (in) x width (in) x length (in) / 144. The examples below all use this form, with lengths sold in feet converted to inches (8 feet is 96 inches).
- With the length left in feet, divide by 12 instead: thickness (in) x width (in) x length (ft) / 12 gives the same answer. Dividing by 144 with the length in feet gives a result 12 times too small.
| Piece | Calculation, all in inches | Board feet |
|---|---|---|
| 1 in x 6 in x 8 ft (96 in) | 1 x 6 x 96 / 144 | 4.00 |
| 1 in x 8 in x 8 ft (96 in) | 1 x 8 x 96 / 144 | 5.33 |
| 2 in x 6 in x 10 ft (120 in) | 2 x 6 x 120 / 144 | 10.00 |
| 1.5 in x 3.5 in x 8 ft (an actual dry 2x4) | 1.5 x 3.5 x 96 / 144 | 3.50 |
| Nominal 2x4 x 8 ft, tallied by label | 2 x 4 x 96 / 144 | 5.33 |
The last two rows differ because the standard that governs softwood sets the tally by label. NIST’s American Softwood Lumber Standard, PS 20-25, defines board measure in section 2.2 as “multiplying the nominal thickness in inches or fraction of an inch by the nominal width in feet by the length in feet.” A nominal 4-inch width is 1/3 foot, so an 8-foot 2x4 tallies 2 x 1/3 x 8 = 5.33 board feet, the same as the table’s 2 x 4 x 96 / 144. Section 2.16 defines nominal size as the label, noting that “a dry 2 by 4 is surfaced to 38.1 mm by 88.9 mm (1 1/2 by 3 1/2 inches).” A softwood 2x4 holds about two-thirds of the wood its tally suggests (3.5 of 5.33 board feet), so a price quoted per board foot and a price quoted per piece are not comparable without this step. The nominal versus actual sizes reference tabulates the common softwood, hardwood and plywood sizes.
How hardwood is tallied
Hardwood follows the NHLA rule, which departs from simple volume in three ways. Surface measure, the face area in square feet, is rounded to the nearest whole foot, and board feet are surface measure times standard thickness. Standard thicknesses under 1 inch are counted as 1 inch. And “in surfaced lumber, board footage is measured before surfacing,” so a board sold surfaced on two sides is tallied at its rough thickness. The rulebook’s table has 1-inch (4/4) rough lumber surfaced two sides to 13/16 inch, and the tally still counts it as 1 inch.
For an 8 in x 8 ft board of 4/4 hardwood, the surface measure is 8 x 96 / 144 = 5.33 square feet, which rounds to 5, so the NHLA tally is 5 board feet even though the volume formula gives 5.33. Suppliers may round differently, so ask how a quote is measured, whether the price is for rough or surfaced stock, and what the minimum purchase is.
Waste factors: derive the allowance from the grade
A single percentage added to every list is guesswork. For hardwood, the grading rules state how much clear wood each grade guarantees, and that gives a derivation. NHLA grades are set mainly by the share of a board’s surface measure that yields clear-face cuttings, within a limit on how many cuttings may be counted. FAS pieces must yield at least 10/12 (83-1/3%) clear-face cuttings, or 11/12 (91-2/3%) when one extra cutting is used. No. 1 Common requires 8/12 (66-2/3%) on pieces of 3 feet surface measure and up, 9/12 (75%) on 2-foot pieces or when one extra cutting is used, and 12/12 (fully clear) on a 1-foot piece. No. 2A Common requires 6/12 (50%) from 2 feet surface measure up, or 8/12 (66-2/3%) on a 1-foot piece or with one extra cutting. These are minimums for a board of that grade, so an individual board can yield more.
The wood you must buy is the area of your parts divided by the yield. The table converts each grade’s minimum into the extra area to buy.
| Grade and NHLA minimum clear-face yield | Board area per 1 sq ft of parts | Extra to buy |
|---|---|---|
| FAS, 10/12 (83-1/3%) | 1.20 | 20% |
| No. 1 Common, 9/12 (75%): 2 ft surface measure, or 3-10 ft with one extra cutting | 1.33 | 33% |
| No. 1 Common, 8/12 (66-2/3%): 3 ft surface measure and up | 1.50 | 50% |
| No. 2A Common, 6/12 (50%): 2 ft surface measure and up | 2.00 | 100% |
The rulebook measures yield in cutting units: one cutting unit is 1 inch wide by 1 foot long, so there are 12 in each square foot of surface measure. A grade yield guarantees an area of clear wood and says nothing about where on the board it lies. The minimum clear cutting in No. 1 Common is 4 inches by 2 feet or 3 inches by 3 feet, so a wide part can fail to fit between defects even when the percentage works out. Lay each part out on the board before buying, and use the table as the first check.
Softwood dimension lumber is bought by the piece, so the allowance there comes from the cut list: assign every part to a board, remove end splits from the usable length, and count the boards.
Turn a cut list into stock lengths
List each part’s quantity, finished length, width, and thickness. Assign the parts to boards, allowing for end trimming, defects, and the measured saw kerf. Total linear feet cannot show whether the lengths fit. Two 48-inch parts and three 36-inch parts total 204 inches, but with 96 inches of stock, two 48-inch pieces cannot share a board once the kerf is removed, because 96 inches of parts plus any cut exceeds the board. A workable layout is 48 + 36 on boards one and two, and 36 on board three. Measure the kerf of your own blade; the examples on this page assume 1/8 inch (0.125). The tape measure guide covers marking cuts so the kerf falls on the waste side.
Area is only a lower-bound check for sheet goods. A 4 x 8 foot sheet has 32 square feet, but grain direction and kerf decide whether the parts fit. Two 24 x 48 inch panels need more than one 48 x 48 inch square once a cut separates them, so sketch the layout before counting sheets.
Fasteners and kits: count from the plan
Count fasteners from the plan, connector, or hardware manufacturer, not from a rule of thumb. Multiply the screws per connection by the number of connections, and keep each length and head type on its own line. Check what a kit already includes. Simpson Strong-Tie’s workbench shelving kit article lists eight RTC2Z connectors and 100 #8 x 1-1/4 inch wafer-head screws in the kit, and says the buyer supplies the 2x4 lumber, the pegboard, and the screws for the top rail and pegboard. A list that does not subtract kit contents buys duplicates.
Worked list 1: repaint a 12 x 14 foot bedroom
Measured: 12 x 14 feet, 8-foot walls, one 3 x 7 foot door, two 3 x 5 foot windows. All quantities below are arithmetic from those measurements and the published ranges cited above.
| Surface | Area | Coats | Product and published rate (sq ft/gal) | Gallons needed |
|---|---|---|---|---|
| Walls | 365 sq ft | 2 | Aura Interior, 350-400 | 1.83 to 2.09; buy 3 one-gallon cans |
| Ceiling | 12 x 14 = 168 sq ft | 2 | Muresco ceiling, 400-450 | 0.75 to 0.84; buy 1 gallon |
| Trim and door | about 83.5 sq ft | 2 | Advance semi-gloss, 400-500 | 0.33 to 0.42; smallest can offered |
The trim area is arithmetic from assumed sizes, 5.25-inch baseboard and 3.5-inch casing. Window casing on all four sides spans 43 x 67 inches less the 36 x 60 opening: 5.0 square feet each, 10.0 for two. Door casing on the top and both sides spans 43 x 87.5 inches less the 36 x 84 opening: 5.1 square feet per side, 10.3 for both. Baseboard runs the 52-foot perimeter less the door and its casings (43 inches), 48.4 feet or 21.2 square feet. Both faces of the door add 42. Replace those heights and widths with your own.
Purchase list: 3 gallons wall paint, 1 gallon ceiling paint, trim paint in the smallest container sold, primer only if the surface calls for it (add its own line), and the product name, color, and sheen recorded on each line.
Worked list 2: a small hardwood bookcase
Plan: two sides 30 in long and three shelves 22.5 in long (24 in overall less two 3/4 in sides), all 7 in wide and 3/4 in thick, cut from 4/4 hardwood sold in 8 in x 8 ft boards, S2S at 13/16 in so each part is planed to 3/4. Assumptions: 1/8 in kerf and 3 in trimmed from each board end, leaving 90 in usable.
- Parts total. 2 x 30 + 3 x 22.5 = 127.5 in of length at 7 in wide, which is 892.5 square inches, or 6.20 square feet.
- Board 1. 30 + 30 + 22.5 = 82.5 in, plus one kerf per part (3 x 0.125 = 0.375 in), is 82.875 in, inside the 90 in usable, with a 7.125 in offcut.
- Board 2. 22.5 + 22.5 = 45 in plus two kerfs (0.25 in) is 45.25 in, leaving a 44.75 in offcut.
- Tally. Two 8 in x 8 ft boards are 10.67 board feet by volume (2 x 1 x 8 x 96 / 144) and 10 on an NHLA tally (5 each after rounding).
- Yield check. 6.20 sq ft of parts at the FAS minimum needs 7.44 sq ft of board (6.20 / 0.833), at 66-2/3% needs 9.30, and at 50% needs 12.40. Two boards give 10.67 sq ft of face, or 10 sq ft of surface measure on the NHLA tally; either covers the first two figures but not the third, so No. 2A Common would call for a third board.
| Line | Quantity | Notes |
|---|---|---|
| 4/4 hardwood, 8 in x 8 ft, S2S | 2 boards (10 bf NHLA tally) | Ask for FAS or No. 1 Common; confirm rough or surfaced billing |
| Wood glue | 1 bottle | Match the joint; see glue types compared |
| Screws | 12 | Assumed schedule: 2 per shelf end x 6 shelf ends; use the plan’s schedule instead |
The glue, screw count, and finish quantity belong to the joinery you choose. The workbench plan and buying checklist applies the same method to a larger job, and the workshop cost guide shows how to price a list once the quantities are fixed.
Before you buy
- Paint: each surface on its own line, a published spread rate for the actual product, and the lower end of its coverage range if the wall is porous or the color change is large.
- Lumber: parts assigned to specific boards with kerf and end trim, and the billing basis confirmed with the supplier.
- Waste: for hardwood, the grade’s yield, not a flat percentage.
- Fasteners: counted from the plan, minus what a kit already supplies.
- Record each assumption next to its quantity so a changed product or dimension can be re-run.
Sources
- Benjamin Moore paint calculator: two-coat assumption, ceiling excluded, rough-estimate caveat.
- Benjamin Moore Aura Interior product page: coverage 350-400, recoat 1 hour.
- Benjamin Moore ben Interior product page: coverage 400-450, recoat 2 hours.
- Benjamin Moore Muresco ceiling paint product page: coverage 400-450.
- Benjamin Moore Advance semi-gloss product page: coverage 400-500, recoat 16 hours.
- Glidden paint calculator: “up to 400 sq. ft.” on primed, smooth, non-porous surfaces.
- NIST PS 20-25, American Softwood Lumber Standard: board measure (2.2) and nominal size (2.16).
- NHLA Rules for the Measurement and Inspection of Hardwood and Cypress (2019 edition): board foot and surface measure (rule 16), S2S thickness table (rule 14), cutting units (37), grade yields (62, 74, 79) and minimum cuttings.
- Simpson Strong-Tie: workbench shelving kit: kit contents and separately purchased materials.