Titebond Original vs II vs III: Data Sheet Comparison
Titebond III is the best default for most shops: it has the longest assembly window of the three (8-10 minutes open, 20-25 minutes total at 70°F and 50% humidity), passes the ANSI/HPVA Type I water-resistance specification, and works down to 47°F. Original suits dry indoor joints that go together quickly. II sits between them on water resistance (Type II) but has the shortest open time of the three, 3-5 minutes, and needs the warmest shop, above 55°F. All three share one weakness that no label hides: Titebond lists each as not for structural or load-bearing applications. The figures below come from Titebond’s technical data sheets as published in November 2026.
The three data sheets side by side
Every value in this table is quoted from Titebond’s technical data sheet for that glue. Times are at 70°F and 50% relative humidity. Where a sheet is silent, the cell says so.
| Item | Original | II Premium | III Ultimate |
|---|---|---|---|
| Chemistry, as the sheet names it | Aliphatic resin emulsion | Cross-linking polyvinyl acetate | Advanced proprietary polymer |
| Open assembly time | 4-6 min | 3-5 min | 8-10 min |
| Total assembly time | 10-15 min | 10-15 min | 20-25 min |
| Minimum application temperature (glue, air and wood) | Above 50°F | Above 55°F | Above 47°F (the same sheet also gives 45°F) |
| Water resistance | Not rated; “not intended for exterior use or where moisture is likely” | Meets ANSI Type II | Passes ANSI/HPVA Type I |
| FDA indirect food contact | Not stated on the sheet | Compliant | Compliant |
| Storage life | 24 months, tightly closed, 75°F | 24 months, tightly closed, 75°F | 24 months, tightly closed, below 75°F |
| Clamping pressure | 100-150 / 125-175 / 175-250 psi (soft / medium / hard woods) | Same | Same |
| Bond strength, room temperature (ASTM D-905, hard maple) | 3,600 psi, 77% wood failure | 3,750 psi, 72% wood failure | 4,000 psi, 57% wood failure |
| Bond strength, 150°F overnight | 1,600 psi, 10% wood failure | 1,750 psi, 6% wood failure | 800 psi, 0% wood failure |
| Submersion | Not for exterior use | Not for continuous submersion or below the waterline | Not for continuous submersion or below the waterline |
| Structural use | Not for structural or load-bearing applications | Same | Same |
Three details are easy to miss. First, the III sheet gives two minimum temperatures: above 47°F in its application guidelines, and 45°F as its chalk temperature and in its limitations. Plan to the higher number. Second, the Original sheet names no water-resistance type at all, so it should not be treated as water resistant in any grade. Third, III is the strongest of the three at room temperature but the weakest in the sheets’ 150°F overnight test, at 800 psi with no wood failure (Titebond Original, II Premium, III Ultimate).
Type I versus Type II water resistance
Both ratings come from laboratory tests, and Titebond’s FAQ describes the ANSI/HPVA procedures behind them (Titebond FAQ). Each test starts with 6-by-6-inch birch laminates glued into three-ply plywood.
| Step | Type I (III passes) | Type II (II passes) |
|---|---|---|
| Specimen size | 1 × 3 inches | 2 × 5 inches |
| Exposure | Boiled 4 hours, baked 20 hours at 145°F, boiled 4 more hours, cooled in running water | Soaked 4 hours, baked 19 hours at 120°F, repeated for three cycles |
| To pass | Sheared while still wet; must meet strength and wood-failure requirements | Bonds must not delaminate |
Titebond calls the Type I test clearly the more stringent. Both tests show how a glue line survives boiling or soaking in a lab; how long an outdoor project lasts depends on more than the glue.
That makes the order of the lineup clear. Original has no rating, II clears the lower bar, III clears the higher one. The II sheet calls Titebond II the first one-part wood glue to pass ANSI Type II, a claim that comes from the manufacturer.
Neither classification licenses submersion. Both the II and III sheets say the glue is not for continuous submersion or use below the waterline. A bond can be water resistant while the joint around it is not: end grain, wood movement and trapped water decide how an outdoor project ages, which is why wood choice matters as much as the bottle (see choosing lumber for the project).
Assembly time decides more glue-ups than strength does
Bob Van Dyke, writing in Fine Woodworking, states the premise plainly: almost all woodworking glues used as directed make a bond as strong as the wood or stronger, “so strength is not the issue” (Woodworker’s guide to glue). Open time is the window before the glued faces must be mated; total assembly time is the window before clamp pressure must be on. III’s windows are roughly double Original’s.
Label times can flatter real work. Van Dyke notes that the labels give Original about 15 minutes and III another 5 to 10, yet finds a tenon “virtually impossible” to slide in its mortise after two or three minutes of assembly, and he does not recommend PVA for tricky joints or glue-ups with many parts unless the work can be broken into stages.
| Glue-up | Choice | Basis |
|---|---|---|
| Edge-glued panel or a single joint | Any of the three | Van Dyke regularly glues up panels with yellow glue |
| Frame with four mortise-and-tenon joints | III, or glue it up in stages | III allows 20-25 min total, against 10-15 for Original and II |
| Mortise-and-tenon assembly with more than four or five joints | Liquid hide glue | Van Dyke’s choice for these and for other complex glue-ups |
| Dovetailed drawer or case | Liquid hide glue | Van Dyke’s choice for all dovetail joints |
The method is the point: time a dry assembly, then choose the glue whose total assembly time exceeds it by a clear margin, or split the job into stages. Temperature is the other limit, because the minimum applies to the glue, the air and the wood. A board that has just come in from a garage at 40°F is below the line for every one of the three glues even in a heated room. Layout of the bench and the stock path matters here; the garage workshop layout guide covers where clamps and assembly space should sit.
Diluting a stiff glue is no way to buy time. Titebond’s FAQ allows most of its water-based wood glues to be thinned with water up to 5% by weight or volume and warns that adding more decreases bond strength.
Clamp time, clamping pressure and when the joint can take load
Titebond’s data sheets give a pressure range but no clamp time. The FAQ fills that gap: for most of the company’s wood glues, clamp an unstressed joint for 30 minutes to an hour and a stressed joint for 24 hours, and do not stress a new joint for at least 24 hours.
The pressure ranges repeated across the three sheets are 100-150 psi for softwoods, 125-175 psi for medium woods and 175-250 psi for hardwoods, with the instruction to use enough pressure to bring joints tightly together. Most home clamps carry no gauge, so the psi figure works as a statement of direction rather than a dial setting: denser wood wants more force, softer wood less.
Three practical points follow from the sheets and the FAQ:
- Clamp time and use time are separate. Removing the clamps at an hour does not authorize lifting the assembly onto a bench to plane it.
- Each sheet gives a minimum spread of approximately 6 mils or 250 square feet per gallon; that is the floor for how much to apply.
- Squeeze-out is cleaned with a damp cloth while wet and scraped or sanded once dry, according to the sheets and FAQ.
Food contact and cutting boards
Titebond II and III both carry the U.S. FDA indirect-food-contact statement on their data sheets, which give cutting boards as the example, and the FAQ says both have been approved for indirect food contact and recommends them for cutting boards. The Original sheet does not make the claim, so a board glued with Original has no manufacturer statement behind it. Titebond’s Instant Bond (CA) page goes further: that glue is not for use on products in contact with food, and the page points to II or III instead (Titebond Instant Bond Medium).
For a board that will be washed often, the glue choice also interacts with water. III’s Type I rating makes it the better fit by the manufacturer’s own classification, though neither II nor III is rated for continuous submersion, so a board should not soak.
Shelf life and storage
Each of the three sheets lists 24 months in tightly closed containers at 75°F (below 75°F for III). The FAQ calls this a conservative estimate of the minimum time the product is expected to remain usable when stored as directed, and adds that most yellow and white glues, including Original and II, stay usable beyond two years, with III expected to last beyond its stated life at room temperature. All three sheets say to keep the glue from freezing; the Original and II sheets add that freezing may thicken it without affecting how it works, and that agitation should restore it. For III, storage above 75°F may thicken the glue and shorten its usable life, and Titebond’s remedy is to shake it vigorously by tapping the bottle firmly on a hard surface.
The FAQ also names the signs that a bottle is finished: Original that has turned thick and stringy, or II that has become an orange-colored gel, is no longer usable. Short of that, Titebond says Original, II and III will perform as intended as long as they stay fluid without a drastic change in appearance.
When PVA is the wrong glue
Four jobs call for something other than a yellow glue, and each alternative has its own manufacturer data.
Hide glue: long working time, reversible joints
Titebond Genuine Hide Glue lists 10 minutes open and 20-30 minutes total assembly at 70°F and 50% humidity, minimum application temperature above 50°F, and 24 months of storage. The page says its sensitivity to moisture allows easy disassembly of parts, which it calls a critical benefit in antique restoration and the repair of musical instruments. It has no water-resistance rating and is not for exterior use or where moisture is likely (Titebond Genuine Hide Glue). Titebond’s 2023 woodworking glue product guide gives its open time as 8-10 minutes and lists “reversible bonds with water” among its features (product guide, PDF). In Fine Woodworking, Van Dyke describes a different liquid hide glue, Old Brown Glue, as having 30 to 45 minutes of working time and a 6 to 12 hour clamp time, and makes it his choice for dovetails and complex glue-ups (Woodworker’s guide to glue). The two products’ figures differ, so the label on the bottle in hand governs.
Epoxy: gaps, outdoor work and boats
In Fine Woodworking, Van Dyke calls epoxy the only gap-filling glue on the market, with open times from 5 to 60 minutes set by the hardener and clamp times from 45 minutes to overnight. West System’s published working times for 105 resin illustrate the range: 60 to 70 minutes for 205 Fast hardener at 72°F in a thin film, up to 3 to 4 hours for 209 Extra Slow, with minimum cure temperatures from 40°F to 70°F (WEST SYSTEM 105 system). West System’s clamping advice differs from the PVA sheets: it advises just enough pressure to squeeze a small amount of the mixture from the joint, warning that too much can squeeze all of the epoxy out, and it describes stirring filler into the epoxy until it is thick enough to bridge gaps between mating surfaces (West System: bonding and clamping).
Polyurethane: moisture cure, cold-weather construction
Titebond’s Fast Set Polyurethane Construction Adhesive page describes a one-component, moisture-cured mastic with 10-20 minutes of open time, an application range of 32°F to 120°F, an 18-month storage life and a waterproof rating that still excludes continuous submersion. It is recommended for construction, installation and repair work, and the page gives no clamp time, only that certain large applications may need bracing until the adhesive cures (Titebond Fast Set Polyurethane). The 32°F minimum, with cold-weather extrusion among its listed features, suits it to cold-weather building work where the yellow glues cannot be used. For wood-to-wood joints, Titebond’s FAQ argues for III over polyurethane glues: a stronger bond, no foaming, less clamp time and water cleanup (Titebond FAQ).
Cyanoacrylate: seconds, small parts
Titebond Instant Bond Medium, an ethyl cyanoacrylate, lists a 5-second set, 7-second handling time, 30-second initial cure, 8 hours to full cure, a 2-year shelf life, and an application temperature above 50°F. It is not for exterior use or where moisture is likely, and its page names uses such as soaking end grain to prevent splitting and gluing pen tubes to blanks (Titebond Instant Bond Medium). In Fine Woodworking, Van Dyke limits CA to workshop jigs and other non-furniture uses because he has heard of long-term failures; he uses it to harden the edges of MDF router templates.
Verdict by joint and use
| Situation | Choose | Reason from the sources |
|---|---|---|
| Indoor box, shelf or frame, quick assembly | Original | 10-15 min total, no moisture exposure |
| Indoor furniture with many parts | III in stages, or liquid hide glue | 20-25 min total for III; Van Dyke prefers hide glue past four or five joints |
| Cutting board | III (II acceptable) | Both carry the food-contact statement; III adds Type I; no soaking |
| Outdoor bench, planter or gate | III, or epoxy | III passes Type I; II’s sheet also names planters and outdoor furniture; Van Dyke’s outdoor choice is epoxy |
| Cold shop, 47-55°F | III; below that, warm the glue, air and wood first | Above 47°F, against 50°F for Original and 55°F for II |
| Dovetails and glue-ups needing unhurried work | Hide glue | 10 min open (Titebond) to 30-45 min working time (Old Brown Glue); reversible |
| Loose or gappy joint, boat or wet exposure | Epoxy | Gap-filling; the hardener sets the working time |
| Cold-weather construction or repair work | Polyurethane construction adhesive | 32°F application minimum |
| Tiny repair, pen tube, split end grain | CA | 5-second set |
| Structural or load-bearing connection | Follow the engineered plan | Excluded on the Original, II, III and hide glue sheets |
A structural frame shows the alternative in practice: the first-workbench plan joins its frame with metal corner connectors and specified screws, and the project material calculator counts those fasteners from the connection details.
Prepare the surfaces
Titebond’s FAQ says these glues are made for bare wood and that the bond over a finish is only as strong as the finish’s hold on the wood. Teak, cedar and redwood can carry an oil or tannin layer that interferes with bonding; recent planing, jointing or sanding removes it, or the surface can be wiped with acetone. The II sheet refers exotic or oily woods such as ipe and teak to Titebond’s Technical Support at 1-800-347-4583, and the III sheet does the same for exotic and oily woods and for exterior doors. The low pH of II and III (3.0 and 2.5) may corrode metal, and Titebond advises a test first where rust is a concern, which matters near steel clamps and cauls.
Sources
- Titebond Original Wood Glue technical data sheet
- Titebond II Premium Wood Glue technical data sheet
- Titebond III Ultimate Wood Glue technical data sheet
- Titebond wood glue FAQ
- Titebond woodworking glues product guide (PDF, 2023)
- Titebond Genuine Hide Glue
- Titebond Fast Set Polyurethane Construction Adhesive
- Titebond Instant Bond Medium
- WEST SYSTEM 105 system hardener table
- WEST SYSTEM: bonding and clamping
- Fine Woodworking: Woodworker’s guide to glue, by Bob Van Dyke (2022)